Product Description Product Specs/Additional Information Related Videos Audio Product Description The ‘Double NFP-Special MKII’ preamp is specifically designed for Multi-coil pickups that feature a “one humbucker per string” coil wiring, simulating Wal MK electronics. The idea is to get a full Humbucker pickup with one pair of coils per string combining them electronically for minimum loading effect and string isolation. This method of mixing the coils brings maximum output, clarity, and punch out of the pickups without any adverse loading effects.The filter controls have sweepable resonant peaks that ranges from 100hz to 2.5 kHz, on the Neck, and 200Hz to 2.5kHz on the Bridge. You can also boost the cut-off frequency(resonant peak) by pulling up the potentiometer.The new ‘Double NFP-Special MKII’ filter preamp features a new Treble boost, labelled ‘Attack’, accessible via a push-pull switch on the Volume potentiometer. This allows to add a narrow set of Treble frequencies to the signal.It offers 6x inputs so that you can wire any multi-coil pickup up to 6 strings.Sweepable filters Range – Neck: 100hz to 2.5khz; Bridge: 200Hz to 2.5kHz.Resonant Peak– 3db standard/ 6db switched (boost accessible via Trim-pot)Voltage operation– 9v to 27vDCCurrent Draw– -3.4mAh (@9v)Filter boards x2: W: 4,4cm; H: 2,6cm; D: 1,7cm Blend board x1: W:3.2cm; H: 2.2cm; D: 1.3cm Potentiometers: Hole size is 6.4 mm and bush height is 10mm. (to be used with 6.4mm knobs) Product Specs/Additional Information To use with multi-coil pickups (1 humbucker per string coil configuration), the ‘Double NFP-Special MKII‘ has dedicated inputs to accommodate this type of pickup and, together, they closely simulate Wal MK electronics. Expect a strong defined sound, with string-to-string separation and definition, as well as all the versatility and punch the NFP preamps line is known for.New FeaturesThe ‘Double NFP-Special MKII’ preamp is specifically designed for Multi-coil pickups that feature a “one humbucker per string” coil wiring, simulating Wal MK electronics. The idea is to get a full Humbucker pickup with one pair of coils per string combining them electronically for minimum loading effect and string isolation. This method of mixing the coils brings maximum output, clarity, and punch out of the pickups without any adverse loading effects.The filter controls have sweepable resonant peaks that ranges from 100hz to 2.5 kHz, on the Neck, and 200Hz to 2.5kHz on the Bridge. You can also boost the cut-off frequency(resonant peak) by pulling up the potentiometer.The new ‘Double NFP-Special MKII’ filter preamp features a new Treble boost, labelled ‘Attack’, accessible via a push-pull switch on the Volume potentiometer. This allows to add a narrow set of Treble frequencies to the signal.It offers 6x inputs so that you can wire any multi-coil pickup up to 6 strings.Sweepable filters Range – Neck: 100hz to 2.5khz; Bridge: 200Hz to 2.5kHz.Resonant Peak– 3db standard/ 6db switched (boost accessible via Trim-pot)Voltage operation– 9v to 27vDCCurrent Draw– -3.4mAh (@9v)Filter boards x2: W: 4,4cm; H: 2,6cm; D: 1,7cm Blend board x1: W:3.2cm; H: 2.2cm; D: 1.3cm Potentiometers: Hole size is 6.4 mm and bush height is 10mm. (to be used with 6.4mm knobs)ures:Treble ‘Attack‘ boost via Push-Pull on Volume potentiometer‘Q‘ variable gain on top of the set gain levelsNeck filter 100Hz to 2.5kHz/ Bridge filter 200Hz to 2.5kHzLonger battery life and lower noise level Check Herrick Pickups, Turner Pickups and Weldang Pickups to find your match. (links on bottom of the text)!!No active/passive switching or coil taping is possible with this pickup/preamp combination!!((You can use this with our 6.4mm Lusithand numbered Knobs)) Related Videos Audio
